Rosewill RNX-N360PC Bedienungsanleitung

Wireless N PCI Adapter RNX-N360PC User Manual 1910020413

6 Figure 2-3 4. Click Browse to change the destination location for the software, then click Next in the screen below (shown in Figure 2-4). Figure

7 Figure 2-5 6. Choose configuration tool, if you are not sure, please leave it default. Then click Next to continue. Figure 2-6 7. Wait a while fo

8 Figure 2-7 ) Note: 1) For Windows XP, the Setup Wizard will notify you of how to proceed with the installation duringthese steps (shown inFigure 2

9select Yes to continue installation. Figure 2-9 8. After all the steps above, you will see the screen below, click Finish to complete the installa

10then the following screen for preparing setup will appear. Figure 2-11 2. Soon, Figure 2-12 will display after a moment. Click Next to continue.

11 Figure 2-13 4. The following page will display and please wait a moment. Figure 2-14 ) Note: For Windows Vista, the Setup Wizard will notify y

12 Figure 2-15 5. Click Finish to complete the installation. Figure 2-16 2.2.4 Software Installation for Windows 7 1. Insert the Resource CD into

13 Figure 2-17 2. Soon, Figure 2-18 will display after a moment. Click Next to continue. Figure 2-18 3. Wait a while for the setup as shown in Figu

14 Figure 2-19 ) Note: For Windows 7, the Setup Wizard will notify you about the Windows Security with the installation during these steps (shown in

15 Figure 2-21

FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

16Chapter 3 Configuration Guide RNX-N360PC can be configured by Wireless N Client Utility. This chapter describes how to configure your Adapter for

17 Figure 3-1 The following table describes the items found on the Current Status screen. ¾ Profile Name - This shows the name of current selected c

18¾ Add a new profile ¾ Modify a Profile ¾ Remove a Profile ¾ Activate a Profile ¾ Import a Profile ¾ Export a Profile ¾ Scan Available Network

19 Figure 3-3 2. Edit the Security tab Select the Security tab in the screen above, and then you can edit the fields to configure the profile. To de

20both the access point and the station. To define shared encryption keys, choose the Shared Key radio button and click Configure to fill in the Defi

21 Figure 3-6 ¾ Power Save Mode - Please select the power save mode in the drop-down list. • Maximum-Selects maximum mode to let the access point b

22Adapter uses. The channels available depend on the regulatory domain. If the adapter finds no other ad hoc adapters, the channel that the adapter s

233.2.4 Export a profile 1. From the Profile Management screen (shown in Figure 3-2), highlight the profile to export. 2. Click Export…, the Export

24Figure 3-9 3.2.6 Scan Available Networks 1. Click Scan on the Profile Management screen (shown in Figure 3-2), the Available Infrastructure and Ad

25 Figure 3-11 3. Highlight the profiles to add to auto profile selection, and click Add. The profile will appear in the Auto Selected Profiles box.

National Restrictions 2400.0-2483.5 MHz Country Restriction Reason/remark Bulgaria General authorization required for outdoor use and public ser

26¾ Broadcast frames transmitted and received ¾ Unicast frames transmitted and received ¾ Total bytes transmitted and received Figure 3-12 3.

27 Figure 3-13 3.4 Configuration for Windows Vista After the Adapter's driver has been installed, Windows Vista will display a wireless Network

28 Figure 3-16 3. To continue, click Connect Anyway. Click the Cancel button to end the connection. Figure 3-17 4. If the connection is successfull

29 Figure 3-18 3.5 Configuration for Windows 7 Wireless N Client Utility is not available for Windows 7. So after the Adapter's driver has been

301. Right-click the icon at the bottom of your screen in your system tray and then you will see the available wireless network list. Select the SS

313. If the key entered is correct, you will successfully connect to the network as shown in Figure 3-21. Figure 3-21

32Chapter 4 WPS Configuration WPS (Wi-Fi Protected Setup) function allows you to add a new wireless device to an existing network quickly. If the wi

33the button on my access point in the next screen shown in Figure 4-4 and click Next. Figure 4-3 Figure 4-4 3. Then wait a minute until Figure 4-

34 Figure 4-5 4.2 PIN method There are two ways to configure the WPS by PIN method: 1) Enter a PIN into your AP device. 2) Enter the PIN from your

35 Figure 4-6 2. Open the Router’s Web-based Utility and click WPS link on the left of the main menu. Then Figure 4-7 will appear. Figure 4-7 3. C

Table of Content Package Contents...1 Chapter 1 Overview ...

364.2.2 Enter the PIN from your AP device 1. Open the WPS Utility and you will see Figure 4-3. Click Next to continue. Then Figure 4-4 will appea

37Appendix A: Specifications Normal Interface 32 bit PCI Interface Standards IEEE802.11n; IEEE802.11g; IEEE802.11b; Operating System Windows 2000/W

38Appendix B: Glossary ¾ 802.11b - The 802.11b standard specifies a wireless product networking at 11 Mbps using direct-sequence spread-spectrum (DS

39¾ SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wire

40Appendix C: FAQ This chapter provides solutions to problems that may occur during the installation and operation of the Wireless Adapter. Read the

413. ‘SSID’ field in ‘Site Survey’ function), you have to input correct SSID of the access point you wish to connect. Please contact the owner of ac

1Package Contents The following items should be found in your package: ¾ One RNX-N360PC Wireless N PCI Adapter ¾ Quick Installation Guide ¾ One Re

2Chapter 1 Overview Thank you for choosing RNX-N360PC Wireless N PCI Adapter. 1.1 Overview of the product The adapter is an 802.11n client device;

3¾ Provides 32-bit PCI interface ¾ Supports Ad-Hoc and Infrastructure modes ¾ Good capability on anti-jamming ¾ Supports roaming between access p

4Chapter 2 Installation Guide 2.1 Hardware Installation To install the adapter, follow these steps listed below: 1. Turn off your desktop PC and d

5 Figure 2-1 2. Soon, Figure 2-2 will display after a moment. Click Next to continue. Figure 2-2 3. After that, you should choose a Setup type. It